Thông số kỹ thuật
Lyzard-KZ1 I
| General | |
|---|---|
| Type: | Point source |
| Transducers: | 0.5″ neodymium magnet woofer |
| Frequency Response: | 500 Hz – 18 kHz (-6 dB)
(1) |
| Max SPL: | 86 dB (peak)
(2) |
| Rated Power: | 3.5 W |
| Coverage: | V. 140° | H. 140° |
| Connectors: | IN+ IN- screw terminals |
| Nominal Impedance: | 16 Ω |
| Handling and Finishes | |
| Dimensions (W x H x D): | 22 x 37 x 11 mm (0.9 x 1.5 x 0.4 in) |
| Weight: | 0.021 kg (0.046 lb) |
| Material: | Aluminum |
| Colors: | Black, White, Custom RAL |
| Regulations | |
| IP Rating: | IP64 |
| EN54-24: | |
(1) With dedicated preset.
(2) Maximum SPL is calculated using a signal with crest factor 4 (12dB) measured at 1 m
Passive loudspeakers requires dedicated preset loaded on board of K-array amplifiers.
New materials and design are introduced into existing products without previous notice.
GeneralType:Point sourceTransducers:0.5″ neodymium magnet wooferFrequency Response:500 Hz – 18 kHz (-6 dB)
(1)
Max SPL:86 dB (peak)
(2)
Rated Power:3.5 WCoverage:V. 140° | H. 140°Connectors:IN+ IN- screw terminalsNominal Impedance:16 ΩHandling and FinishesDimensions (W x H x D):28 x 43 x 11 mm (1.1 x 1.7 x 0.4 in)Weight:0.021 kg (0.046 lb)Material:AluminumColors:Black, White, Custom RALRegulationsIP Rating:IP64EN54-24:
Truffle-KTR24
| General | |
|---|---|
| Type: | Passive subwoofer |
| Transducers: | 4″ woofer + passive radiator |
| Frequency Response: | 45 Hz – 150 / 500 Hz (-6 dB)(1) |
| Max SPL: | 112 dB (peak)(2) |
| Coverage: | Omni |
| Rated Power: | 60 W |
| Connectors: | 2PIN euroblock connector (included) |
| Nominal Impedance: | 4 Ω |
| Handling and Finishes | |
| Dimensions (W x H x D): | 122 x 117 x 199 mm (4.8 x 4.6 x 7.8 in) |
| Weight: | 1.5 kg (3.31 lb) |
| Material: | Aluminum |
| Colors: | Black |
| Finishes: | Powder Matte |
| Regulations | |
| IP Rating: | IP64 |
(1) With dedicated preset
(2) Maximum SPL is calculated using a signal with crest factor 4 (12dB) measured at 1 m.
Passive loudspeakers requires dedicated preset loaded on board of K-array amplifiers.
New materials and design are introduced into existing products without previous notice.
Kommander-KA02 I
| General | |
|---|---|
| Type: | 4ch switching mode, Class D Amplifier |
| Output Power: | 4x 50 W @ 4 Ω |
| Impedance: | minimum 4 Ω (2 Ω PBTL) |
| Frequency Response: | 20 Hz – 20 kHz (±1 dB) |
| Connectors: | Input: 4x BAL input: Euroblock 1.5/ 3-ST-3.81, 3.5 mm jack unBAL analog stereo AUX input, TOSLINK optical input, Output: 2x Euroblock 2,5/ 4-G-5,08 Digital: 4x USB-A 2.0, 1x RJ45 Ethernet, Bluetooth 4.1 Low Energy, Wi-Fi IEEE 802.11 b/g/n |
| Built-in DSP: | Grouping, Input EQ, Output EQ, Signal Routing, Level adjustment, Dynamic Limiters, Delay |
| MAIN Operating Range: | Dedicated AC/DC power adapter 100-240V ~ AC, 50-60 Hz input / 24 V, 4 A DC output |
| Remote Control: | Wi-Fi dedicated K-array Connect mobile app. Ethernet wired K-framework3 multiplatform design and tuning software |
| Power Consumption: | 20 W @ 4 Ω load, Pink noise, 1/8 rated power |
| Protections: | Over Temp. (Power Limiting – Thermal Shutdown), Short Circuit/Overload Output Protection, Power Limiting, Clip Limiter/Permanent Signal Limiter, High Frequency Protection |
| Handling and Finishes | |
| IP Rating: | IP20 |
| Dimensions (W x H x D): | 219 x 45,5 x 170 mm (8.6 x 1.8 x 6.7 in) |
| Weight: | 0.7 kg (1.5 lb) |
| Material: | Aluminum |